Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 15:50:57 GMT
Yep, that's exactly what I mean. The color denotes it's use. Brown and gray are for metal. The colors also denote the "grit" of the scotch brite pads. Here is a pdf that shows the each grit for each color. I normally use the gray (7448) pad on my swords. I am pretty sure this is also the pad that Albion supplies with their swords. here is the link to the pdf: yeoldegaffers.com/sbg/scotchbrite.pdfYep; you're essentially scuffing off the old finish and bringing it down to a less mirror polish level. If I'm not mistaken, it's some kind of enamel they have on it... M. Windlass used to use a laquer on some of their swords, but I havn't seen that in a long time. Most of their swords are finished with a pretty good shine, and by using the gray pad you can put a nice satin finish on the steel. On the other hand some of my swords I like the gloss look better.. just a matter of taste. The sword pictured below shows a before and after shot. This model had NO laquer on it, and I just toned down the shiny steel a bit using the gray pad. Edit: I meant to mention that I pick these up at automotive stores. I normally have to ask for them at the counter as they sometimes do not stock them on the shelves. -gaffer
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 16:11:00 GMT
I actually like the toned-down look as opposed to the ultra-shiny. Now, if I could just figure out how to 'unblacken' my coif, I'd be good.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 20:24:14 GMT
Does Albion use those same pads to give their swords the trademark satin finish? Could you do the same thing to any sword?
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 20:47:45 GMT
Jonathan, yes and yes. That is, Albion includes said pads with every sword they sell...if they stand by them, it stands to reason they use them as well. And yes, you could do that to any sword, provided you have the time and patience- and elbow grease!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 21:46:17 GMT
This is very nice to know. I plan on purchasing one of those pads when I do get my swords.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 21:49:29 GMT
Does Albion use those same pads to give their swords the trademark satin finish? Could you do the same thing to any sword? Jonathan, As Ebon states, yes and yes! If you would like to see some more before and after shots of my sword go to the bottom of this page: /index.cgi?board=swordcustom&action=display&thread=10336&page=2Also, here is the "how to take care of an albion page" that might be of some interest to you. www.albion-swords.com/swords/albion/sword-care.htmIt does take a bit of work, but I really like the results, and it makes taking care of the sword down the road much easier. If I get a little scratch or something from cutting or (heaven forbide!) some rust, a little touch up with the gray pad makes it look new again. btw.. I also use the CLP oil the albion page mentions.. I really like it.. my favorite oil so far. -gaffer
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 21, 2009 22:07:18 GMT
Thank you, Yeoldgaffer. It will be an interesting experience trying to make a European Hanwei blade have the finish of an Albion, but it will be worth the effort.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 22, 2009 2:00:53 GMT
Ebon, fill a bucket half way with sand, toss in your coif, seal it, and roll it around a good while.
M.
|
|